Ir remote control Switch

                                       Ir remote Control Switch

This project describes a technique of adding the remote control feature to an electrical appliance. The goal is to construct a black box where you can plug-in your 120V AC appliance (it can be easily modified for 220 V mains supply too) and control the ON and OFF operations with a TV or DVD remote that uses modulated infra-red (IR) pulse train of 38 KHz frequency. I did this project for my wife who studies late at night on her bed and later feels tired to stand up and turns the light off. Now she does it from bed with the TV remote. The good thing about this project is that it does not use any microcontroller and is only based on the CD4017 decade counter IC.

The original circuit diagram for this project was published in the May 2005 issue of the magazine. The circuit diagram below is mostly the same. It uses a TSOP1738 IR receiver module at the input side to receive the 38 KHz frequency IR pulses from the remote control. Under normal condition, the output pin of the IR module is at logic High, which means the transistor T1 (BC557 PNP) is cut-off and its collector terminal is at logic Low. The collector of T1 drives the clock line of the CD4017 decade counter.

Now lets see what happens when somebody faces a TV or DVD remote towards the TSOP1738 and presses any key on it. The TSOP 1738 module receives the train of 38 KHz IR pulses from the remote, that makes its output to oscillate too. These pulses are inverted at the collector of T1, which finally go to the clock input of the decade counter. The arriving pulses could increment the CD4017 counter at the same rate (38 KHz), but because of the presence of the RC filter circuit (R1 = 100K, C1 = 10 uF) between the collector and the ground, the train of pulses appear as a single pulse to the counter. Thus, on each key pressing, the CD4017 counter advances only by a single count. When the user releases the key, the C1 capacitor discharges through the R1 resistor, and the clock line is back to zero. So every time the user presses and releases a key on the remote, the CD4017 counter receives a single pulse at its clock input.

Initially, when the circuit is just powered on, the Q0 output of the CD4017 decade counter goes high. The counter increments for each low-to-high going pulse arriving at its CLK pin (14). When the first pulse arrives, Q0 goes Low and Q1 is turned High. This activates the relay and the AC appliance connected to it is turned on. The status LED connected to Q1 also glows to indicate the appliance is switched on. When the user presses a key again, the second pulse arriving at the CLK line increments the counter by 1. This makes Q1 back to Low (which means the relay is deactivated and the appliance is turned off) and Q2 is pulled High. Since Q2 is wired to the Reset input, the second key press actually brings the CD4017 IC back to the power-on-reset conditions with Q0 High. Thus, it basically operates as an ON/OFF toggle switch controlled with any key of an infrared remote.

The power supply for the circuit can be derived from the mains AC itself using a step down transformer and a bridge-rectifier circuit. For +5V power supply, the LM7805 regulator IC can be used as shown below.

Parts Ruquired

3way Terminal block x 3

Schrack SPDT 16A 24VDC Relay x 3
1N4148 Diode x 3
BC547 Transistor x 3
3way Berg strip x 1
10KOhms Resistor x 5
470Ohms Resistor x 5
5mm LED x 3
3mm LED x 1
TSOP 1738 x 1
LM7805 IC x 1 (+ its filter parts - 470microfarad 50V electrolytic capacitor, 10nanofarad ceramic capacitor x 2, heatsink if necessary)
LM7824 IC x 1 (+ its filter parts - 2200microfarad 50V electrolytic capacitor, 330nanofarad ceramic capacitor, 100nanofarad ceramic capacitor )
Programmed PIC12F629 IC (Program Included)
8Pin IC Holder
240VAC to 24VDC 1A Adaptor + its female
A strip board to accommodate above
A Plastic Box to accommodate above + small screws and nuts
SONY REMOTE